Swamp cooler water line fittings. www.esleepy.com: Camco 10196 by Brass Compression Fittings for Evaporative Coolers 2019-01-12

Swamp cooler water line fittings Rating: 7,7/10 587 reviews

FPTxMPTx1/8'' Tap Evaporative Cooler Fitting — 120EC

swamp cooler water line fittings

This is simply a threaded hole in the side of it so you can screw in a valve. Use a damp rag to pick up any remaining dust and to get into corners and tight spaces. Prices subject to change with market fluctuation. Am I doing something stupid here, or is there something I'm not getting? Also, you should also always use two wrenches when tightening - one to hold the fitting from turning, the other to tighten the compression nut. Well i have created this beginners guide to pc water cooling fittings to try and help address some of the fears some people might have in regards to water cooling and which are the best fittings people should buy for their first water cooling loop. Plastic water line is much easier to install since it can be easily bent to follow the contours of a home or any building.

Next

How to Hookup or Repair a Swamp Cooler Water Line

swamp cooler water line fittings

The best time to rough in your swamp cooler wiring and water line for your new cooler is after the holes are cut through the roof and ceiling, but before the ductwork is installed. This forum is a valuable resource, whether you get a little sass or not. An unsteady mesh can cause the padding to protrude and cause severe splashing of water. Confirm that the motor is running and the fan wheel is turning. The diagram to the left is a very typical rambler style one level home with a basement mechanical room. QuietCool is so energy efficient that it costs about the same to operate as a large floor fan — about a dollar per day.

Next

FPTxMPTx1/8'' Tap Evaporative Cooler Fitting — 120EC

swamp cooler water line fittings

The water that's discarded by the purge pump can be used to irrigate a nearby garden, plants, or trees so it isn't wasted. Into the convenient side tap. This valve is designed just for this purpose. Specially designed for evaporative cooling so there is no excess load on the fan. Featuring quarter-turn lever handle flow control the. Loose pads tend to deflect the water. Pull the water line out the top of the roof jack and route to this location.


Next

Compression fitting won't fit on evaporative cooler supply line

swamp cooler water line fittings

Use this bearing if your cooler is equipped with a high-rise bearing assembly. Hooking into a home water line for a swamp cooler can be done a few different ways depending on the placement of a unit and types of water pipes. So, I figured I'd just cut out that small piece and use a compression union fitting to connect it back together. That runs from our outside spicket to the swamp cooler, in the process pinching the line. This is a two speed switch with fan only option and pump only option. When it was fired up this season I put a bucket under it to catch the water for reuse.


Next

Hose Adapter; Garden Hose to Float Valve 9056

swamp cooler water line fittings

Now you are becoming argumentative. Befuddled and getting different answers depending on who I ask. Inline filters can be installed anywhere on a water line before the evaporative cooler. Inspect the inner surface of the compression nut and its washer. Prevent corrosion and help keep the in your cooler from building up with a zinc anode rod. If the swamp cooler wiring can be done now without interfering with the ductwork installation, you will be a much happier Do-It-Yourselfer. Connect the tubing to the cooler's compression thread with a compression nut, plastic ferrule, and tube insert.

Next

Supplying Water To A Swamp Cooler

swamp cooler water line fittings

For a swamp cooler to cool the air, it needs water. Local store prices may vary from those displayed. Use the same routine on the plastic side and a brass ferrule on the copper. Summary Hooking a water line to an evaporative cooler is not a difficult job but be sure to call a professional if in doubt. To use most cleaner products, you pour a measured amount of cleaner directly into the water in the evaporative cooler pan, then you run the cooler on pump mode for about 20 minutes. It cleans the water in the cooler automatically every 6 to 8 hours of use by pumping a percentage of the water out of the pan so it can be replaced with fresh water. The local hardware store folk insist, sometimes, that a compression fitting will work if you apply enough torque.


Next

Products for Maintaining Your Evaporative Swamp Cooler

swamp cooler water line fittings

I live in el paso tx. The washer should be replaced if it seems worn-out. Use a wire brush to scrape-off such deposits. You might also try lightly sanding the copper pipe to smooth it out. Look to see if the pipe is properly positioned on to its drain hole.

Next

Connecting a Swamp Cooler line To a Outside Faucet

swamp cooler water line fittings

Once again, if it is practical, placing the switch on the outide of the flue chase can be a good option. So, lets do a little history. If you get the internal reinforcement sleeve and the proper compression ring for the plastic tubing, it will seal without problems. If this is the case, you need to replace the float valve. This means finding a compression thread to flare thread adapter coupler , a nipple to get outside of the cooler, and another flare coupler to attach the tubing to.


Next